Error Detection and Pattern Prediction Through Phase II Process Monitoring

Azam Zaka,Riffat Jabeenand Kanwal Iqbal Khan

1Government Graduate College of Science,Wahdat Road,Lahore,Pakistan

2COMSATS University Islamabad,Lahore Campus,Lahore,Pakistan

3Institute of Business&Management,University of Engineering and Technology,Lahore,Pakistan

Abstract:The continuous monitoring of the machine is beneficial in improving its process reliability through reflected power function distribution.It is substantial for identifying and removing errors at the early stages of production that ultimately benefit the firms in cost-saving and quality improvement.The current study introduces control charts that help the manufacturing concerns to keep the production process in control.It presents an exponentially weighted moving average and extended exponentially weighted moving average and then compared their performance.The percentiles estimator and the modified maximum likelihood estimator are used to constructing the control charts.The findings suggest that an extended exponentially weighted moving average control chart based on the percentiles estimator performs better than exponentially weighted moving average control charts based on the percentiles estimator and modified maximum likelihood estimator.Further,these results will help the firms in the early detection of errors that enhance the process reliability of the telecommunications and financing industry.

Keywords: Reflected power function distribution; exponentially weighted moving average; extended exponentially weighted moving averages; modified maximum likelihood estimator; percentile estimator

1 Introduction

The scholars are anxious to know about the error tendency during the entire manufacturing process to validate the pre-production testing results.It was expected during the machine installation process that the pre-testing results remain valid in the practical life, and also errors remain in control for instance, laptop manufacturing, which passes through several processes.The final product should be error-free when it is delivered to the market for sale as the complaints from distributors and customers can harm the firm’s reputation.Therefore, companies follow a rigorous monitoring procedure to identify and handle faults at the early stages.An efficient monitoring system can minimize the likelihood of product failure and improves its quality.That is why organizations paid attention to develop a system that can identify errors at an initial stage and keep them in control overtimes.In this way, it not only increases the efficiency of the product but also enhances its productivity.

However, the underlying situation of the production process may not be as normal in practical life as expected.That is why the error distribution of the manufacturing concerns is not normal and often follows a reflected power function distribution (RPFD).Therefore, there is a need to apply the RPFD under such real-life situations, where normal distribution failed to assess the error patterns.The current study used the RPFD from Zaka et al.[1] in process analysis, reliability testing, and error predicting.We also introduce control charts based on the assumptions that if the number of errors follows the RPFD and there exists a non-random variation in the distribution,then errors can be determined and handled at the initial stage.These control charts make the monitoring process of a machine more reliable and also provides persistent results.

Previously scholars constructed control charts based on the normality assumption.However, few studies like Roberts [2] recommended including exponentially weighted moving average(EWMA).Some studies currently discussed different control charts for real-life situations where normality assumptions do not fulfil [3-15].These real-life applications of the control charts motivate scholars to explore them in non-normal cases where error patterns are unpredictable,particularly in manufacturing concerns.It helps the practitioners in the early solution to the errors that further lead to continuing the process without any interval, ultimately saving time and cost.It also develops the customers’confidence in the corporations through a continuous quality improvement process.

Generally, statisticians deal with two types of data processing.The first type provides the complete information about the variable of interest, while the second one often depicts misleading or sometimes based on basic details about the study variables.The present study is conducted in the first type of data when the process yields all the observations and follows the RPFD.However,the second type of data is more appropriate for neutrosophic statistics and is used in the literature to make the control charts.The scholars Aslam et al.[9-11], Aslam [12], Aslam et al.[13], and Khan et al.[14,15] have provided empirical support to these arguments.

This study has an added advantage over existing papers on control charts; first, it is applicable in most situations when the normality of any process is in doubt.We have found limited literature [2-15] discussing practical life scenarios.Thus, the current work may be a valuable addition to the literature.Second, it can be extended to neutrosophic statistics by providing the control charts when the process provides indeterminate data without assuming the normality of the process distribution.

We have the following breakage of the manuscript: Section 2.1 provides us with the RPFD and its estimators.Then, we have constructed an EWMA chart and presented it in Section 2.2,and the EEWMA chart is developed in Section 2.6.Simulation study and real-life application are discussed in Section 3, and then finally conclusion is drawn in Section 4.

2 Materials and Methods

2.1 Proposed Process Monitoring for Reflected Power Function Distribution

Using Zaka et al.[1] and assumingx1,x2,x3,...,xtbeing independent identically distributed random variables follows the RPFD as given below

and

where “θ” is the reflecting parameter.Also,γ,βare the shape and scale parameters.From Zaka et al.[1], MMLM and PE estimators are defined below,

and

where H = maximum percentile, L = minimum percentile and P = percentile

2.2 EWMA Control Chart Using PE

whereEWPEt-1represent the EWMA statistic for the preceding time.Andλis a smoothing constant.We refer the Zaka et al.[16] to get the details on generalizing EWMA Statistics,

Using Zaka et al.[16], we get

Alternatively, we get

The control limits are,

where 1-(1-λ)2ttends to unity iftapproach towards larger observation.The control limits are defined below

2.3 EWMA Control Chart Using MMLM

We define the EWMA statisticas

2.4 Algorithm Used for EWMA Control Charts Using PE and MMLM

We generate a random sample from the process following RPFD using the sample size of 150.We then compute the estimate of the shape parameter using PE and MMLM alternatively and get their means and variances.Finally, the control limits using PE and MMLM are computed,and ARL is computed.We have fixed ARL0 = 500.Now we assume that the process parameter is shifted from its true value.We take different shifts and computed ARL for shifted process and called it ARL1.We have repeated this process 5000 times.Using the algorithm approach above,it is observed that the EWMA chart is helpful in the detection of small shifts at the early stage of the distribution.Here, we apply ARL criteria to compare the efficiency of an EWMA and EEWMA for both estimation methods.

From Tabs.1-3 and Figs.1-3, we observe an increasing behavior in ARL for the EWMA control chart with an increase in the value of λ using PE and MMLM to estimate the distribution parameters.We note that as λ gets close to 1, there is less variation in the ARLs.Also, from Figs.2 to 4, we note that the control chart based on PE performs better than the control chart based on MMLM.

Table 1: ARLS for EWMA control charts using PE and MMLM (λ= 0.2)

Table 2: ARLS for EWMA control charts for PE and MMLM estimators (λ=0.6)

(Continued)

Table 2: Continued

Table 3: ARLS for P.E and MMLM estimators based EWMA control charts (λ=0.75)

2.5 The Traditional Extended Exponentially Weighted Moving Averages(EEWMA)Control Chart

When the distribution of the process is normal, the EEWMA control chart was introduced by Naveed et al.[17].The EEWMA control chart by Naveed et al.[17] is given as

Zt=λ1Tt-λ2Tt-1+(1-λ1+λ2)Zt-1

where 0 ≤λ1≤1 and 0 ≤λ2≤λ1.Tt-1is represents the previous value of the variable andZt-1denotes the previous value of the statistic.

The mean and variance are given as

E(Zt)=μ

And

Figure 1: ARLS for EWMA control charts (λ=0.2)

Figure 2: ARLS for EWMA control charts taking λ=0.6

Figure 3: ARLS for EWMA control charts (λ=0.75)

Figure 4: ARLS for MMLM and PE-based EEWMA control charts taking λ1=0.90,λ2=0.20

2.6 Proposed EEWMA Control Chart Using PE

The EEWMA statistic using PE of the shape parameter of the RPFD using Zaka et al.[1]and Naveed et al.[17] is stated by

taking t = 1, 2 anda=(1-λ1+λ2), we get

Letb=(aλ1-λ2)and solving

On generalizing above, we get

By taking expectation and Replacingb=(aλ1-λ2)we get

By using geometric series, we get

2.7 Proposed EEWMA Control Chart Using MMLM

The EEWMA statistic using the mean and variance given in (13) and (14).The control limits are given as

2.8 Algorithm for EEWMA Control Charts Under PE and MMLM

We generate a random sample from the process following RPFD using the sample size of 150.We then compute the estimate of the shape parameter using PE and MMLM alternatively and get their means and variances.Finally, the control limits using PE and MMLM are computed,and ARL is computed.We have fixed ARL0= 500.we take different shifts and computed ARL for shifted process and called it ARL1.We have repeated this process 5000 times.

Using the above algorithm, we observe the clear efficiency of EEWMA over EWMA using PE and MMLM.The ARLs are presented in Tabs.4 and 5 for both PE and MMLM.We observe that for largerλ1, we get a large ARL value.We also see that EEWMA control chart increases if the value ofλ1is increased.Also, we see from Figs.4-6 that the ARLs for EEWMA under PE remain less than ARLs for MMLM based EEWMA control chart.Additionally, we see that PE provides more efficient control charts compared to the MMLM for monitoring a process that follows RPFD.

3 Results and Discussion

The 50 observations are generated using RPFD.Half of which is generated for the process to be in control and the other half are created by a shift of 0.40.We presented the estimates for the shape parameter of RPFD using MMLM and PE are calculated in Tab.6, Figs.7 and 8, illustrate the estimates from EEWMA.We see that PE-based on the EEWMA control chart detects an out-of-control state earlier than MMLM.

Table 4: ARLS for MMLM based EEWMA control charts

(Continued)

Table 4: Continued

Table 5: ARLS for PE-based EEWMA control charts

(Continued)

Table 5: Continued

(Continued)

Table 5: Continued

Figure 5: ARLS EEWMA control charts(λ1=0.50,λ2=0.75)

Figure 6: ARLS EEWMA control charts (λ1=0.90,λ2=0.75)

Table 6: Simulated results for LCL and UCL based on proposed EEWMA

(Continued)

Table 6: Continued

(Continued)

Table 6: Continued

Figure 7: Proposed EEWMA control chart using MMLM (L = 12, λ1=0.90 and λ2=0.75)

Figure 8: Proposed EEWMA control chart using PE (L = 7.66, λ1=0.90 and λ2=0.75)

3.1 Real-Life Application

The Real-life data is taken from the operation side of the telecommunication industry, where errors in the software frequently occurred regarding the billing amount, dispatch issue, contact and login details.The per-day frequency of errors in the software is reported below: 1124, 1013, 1187,1153, 1141, 1051, 1178, 1145, 1124, 1132, 1141, 1136, 1241,1301, 1214, 1421, 1258, 1109, 1321,1121,1114, 1021, 1131, 1142, 1165, 1184.The data followed the RPFD and plotted for EEWMA control charts under MMLM and PE, as shown in Figs.9 and 10.

Figure 9: Graph of real data of the EEWMA control chart under MMLM when L = 12, λ1=0.90 and λ2=0.75

We have constructed EEWMA control charts on real-life data under MMLM and PE.For example, in Figs.9 and 10, we see that EEWMA under PE predicts the process shift at early levels compared to EEWMA under MMLM, which indicates that EEWMA under PE provides a better explanation of the distributions when the underlying process is based on RPFD.

Figure 10: Graph of real data of the EEWMA control chart under PE when L = 7.66, λ1 =0.90 and λ2=0.75

3.2 Earnings Per Share(EPS)of the National Refinery Ltd

Real-life data for earnings per share (EPS) of the National Refinery Ltd.were taken from the State Bank of Pakistan (SBP) report for non-financial companies from the year 1984-2019.The data in Tab.7 followed the RPFD and plotted for EEWMA control charts under MMLM and PE, as shown in Figs.11 and 12.

Table 7: State Bank of Pakistan (SBP) report for non-financial companies from the year 1984-2019

We have constructed EEWMA control charts on real-life data under MMLM and PE.For example, in Figs.11 and 12,

We see that EEWMA using PE better predicts the process shifts using less samples as compare to MMLM.So it can be used effectively for Earning per share data.

Figure 11: Graph of real data of the EEWMA control chart under MMLM when L = 12, λ1=0.90 and λ2=0.75

Figure 12: Graph of real data of the EEWMA control chart under PE when L = 7.66, λ1 =0.90 and λ2=0.75

4 Conclusions

This study is conducted to develop the control charts in a real-life situation that does not follow a normal distribution by employing statistical methods.The main findings of the study are:

? It discussed the application of the RPED in the production process of telecommunications and finance.

? It has applied two memory-based control charts and suggested that EWMA and EEWMA based on PE and MMLM are better estimators when the underlying distribution follows the RPFD.

? Further, we compared the performance of each control chart with a PE-based EEWMA control chart.We concluded that PE-based control charts are an effective estimator for the early deduction of machine errors.It can even identify minor shift errors more efficiently than MMLM-based estimators if a distribution works under the RPFD function.

? These results can be beneficial for scholars and practitioners of the diversified field of management and applied sciences.It will help them design the strategies to cope with the errors during the production process that improves product quality and eventually cause high returns.

Data Availability:The data used to support the findings of this study are included in the article.

Funding Statement:The authors received no specific funding for this study.

Conflicts of Interest:The authors declare that they have no conflicts of interest to report regarding the present study.