A Novel Beamforming Emulating Photonic Nanojets for Wireless Relay Networks

Samer Alabed,Ibrahim Mahariq,＊,Mohammad Salman and Mustafa Kuzuoglu

1College of Engineering and Technology,American University of the Middle East,Kuwait

2Department of Electrical and Electronics Engineering,Middle East Technical University,Ankara,06800,Turkey

Abstract:In this article,a low-cost electromagnetic structure emulating photonic nanojets is utilized to improve the efficiency of wireless relay networks.The spectral element method,due to its high accuracy,is used to verify the efficiency of the proposed structure by solving the associate field distribution.The application of optimal single-relay selection method shows that full diversity gain with low complexity can be achieved.In this paper,the proposed technique using smart relays combines the aforementioned two methods to attain the benefits of both methods by achieving the highest coding and diversity gain and enhances the overall network performance in terms of bit error rate(BER).Moreover,we analytically prove the advantage of using the proposed technique.In our simulations,it can be shown that the proposed technique outperforms the best known state-of-the-art single relay selection technique.Furthermore,the BER expressions obtained from the theoretical analysis are perfectly matched to those obtained from the conducted simulations.

Keywords:Wireless relay networks;cooperative diversity techniques;relay selection;network beamforming techniques

1 Introduction

In wireless communication systems,several techniques have recently been suggested to improve the overall system performance in terms of bit error rate(BER)or achievable data rate[1–9].Some of them are based on increasing or optimizing the transmitted power or based on using efficient error detection and correction to improve the overall coding gain of the BER curves.Recent techniques are implemented based on improving diversity gain by applying time diversity,frequency,special diversity or a combination of them.Time diversity can improve the BER curve by sending the same information symbols several times in different time slots.Frequency diversity enhances the BER performance by transmitting the same information symbols several times in different frequency slots.

Spatial diversity techniques also known as multiple-input multiple-output(MIMO)techniques can improve the BER performance by sending the same information symbols several times using different transmitted antennas at the same time and frequency slots.The latter techniques are considered as being the most efficient ones since they do not require additional time or frequency slots[3–9].To improve both diversity and coding gain,many recent techniques that combine some of the diversity techniques have been proposed such as space-frequency coding(SFC)techniques and space-time coding(STC)techniques[2,8].

Other special diversity techniques based on beamforming schemes[4–6]which multiplies the transmitted antennas by certain factors to enable beam steering in the direction of the receiving antennas have been suggested to improve the overall performance in terms of BER and the achievable data rate.This is because MIMO communication systems are greatly affected by the multiuser interference and channel impairments such as the time varying fading caused by multi path propagation[1–9].

In many applications,it is difficult,due to several limitations,to have many antennas on the mobile station.To solve this problem,a cooperative communication system can be performed instead of applying the conventional MIMO systems by using relay nodes distributed randomly between the transmitted antennas.These relays are used either to just amplify-and-forward(AF)the received signals or they can decode the information signals before broadcasting them to the received antenna.Therefore,in cooperative communication networks,relay-nodes will jointly process the received data messages before broadcasting them using their antennas toward the receiving entities,which will combine all the received copies from different paths to improve the spatial diversity gain.Such techniques are called the multi-antenna diversity techniques that incorporate the use of one-way or two-way relaying schemes[1–7].

Recently,many efficient relaying techniques are proposed to achieve the full diversity gain and the highest coding gain such as distributed space time coding techniques which allow the relays to apply space time coding technique to improve the overall system performance[2,3],distributed beamforming techniques which allow the relay to form a beam in the direction of the receiver to improve the overall received signal-to-noise-ration(SNR)thus offering higher coding gain[4–6].

The previous two techniques use all relay nodes between the communicating terminals.To improve the previous techniques and achieve the full diversity gain with low decoding complexity in non-orthogonal relay-node networks and without using all relay nodes between the communicating terminals,relay selection techniques have been proposed[10–19].In the latter techniques,a single relay[10–12]or two relays[13,14]among several relay nodes between the communicating terminals are selected to amplify and forward the received signal to decode and forward it to the destination.These techniques enjoy full diversity gain and low overall complexity by using only one or two relays.In[10–12]a single relay-node is selected among a set of relay nodes to maximize either the SNR or the achievable data rate.In[11,12],a criterion is proposed to select the optimal relay node using the max-min scheme.

In the conventional wireless relay networks,each relay node is equipped with a single antenna or several antennas to receive the signal before amplifying and forwarding it.In this paper,the received signal is improved prior to processing it by focusing the beam to the relay antenna using a specific element designed and simulated by the spectral element method(SEM)which is recently applied in electromagnetic radiation to improve the channel gain of each relay node.

In order to achieve accurate results,SEM has been utilized in this study for the computation of transmitted and scattered fields.In fact,this method has been recently applied in electromagnetic radiation and/or scattering problems due to its accuracy and the relatively lower computational requirements[20–26].For accuracy demonstration,the authors in[24]compared the computational relative error among SEM,finite element method and finite difference method in several one- and two-dimensional problems and reported exceptional accuracy for the case of SEM with much less computational cost.

In this work,both beamforming technique emulating photonic nanojet behavior[26–30]and the optimal single-relay selection method have been combined in this proposed technique to obtain the benefits of both methods.An electromagnetic structure is proposed to enhance the efficiency of the relay nodes while the relay selection method is improved to achieve the full diversity gain with low decoding complexity.By combining both methods,the proposed technique using smart relay enjoys the highest coding and diversity gain and improves the overall system performance in terms of BER.In this article,we prove that the performance of the suggested strategy is better than the performance of the best known state-of-the-art single relay selection technique.Furthermore,we prove that the BER mathematical expression of our theoretical analysis is perfectly match those obtained from the conducted simulations.

2 Materials and Methods

For our system model,we consider a one-way relay network consisting of a singleantenna transmitterT1,a single-antenna receiverT2,and R single-antenna smart-relay nodes(R1,...,RR)distributed randomly between the transmitter and receiver.In the first phase,the transmitterT1sends its information symbol to all smart-relay nodes.This intermediate relay-node is selected from a group ofRsingle-antenna relay-nodes(R1,...,RR)that are located between the transmitter and the receiver as shown in Fig.1.In this work,the best relay is selected based on max-min criterion.In case of the AF protocol is used,the selected relay is going to amplify and forward the received signal to the destination terminalT2while if the decode-and-forward(DF)protocol is used,then the selected relay decodes the information symbols received from the transmitter before amplifying and forwarding the decoded information symbol to the destination terminalT2.Note that the transmitterT1,receiverT2,and the selected relay-nodeRshave limited average transmit powersPT1,PT2,PRs,respectively.Furthermore it is assumed that the channel gains,from the relay-nodes to the terminals and vice versa,are reciprocal for transmissions,and we denote them asfr(fromT1toRr)andgr(fromT2toRr).Furthermore,the following notations |.|,?.」,‖.‖ andE(.)are used to denote the absolute value,the floor function which rounds toward zero,the Frobenius norm,and the statistical expectation,respectively.

Figure 1:System model

3 The Proposed Relay Selection Technique

In this proposed technique,one intermediate relay node will be chosen from the R relay nodes where the optimal single relay nodeRsis chosen among the R available intermediate relay nodes according to the max-min selection technique[10–14]based on the below equation:

Note here that the decoding complexity is very low,as a symbol-wise decoder which enjoys a linear decoding complexity is being used to detect the received data messages.

4 Definition of the Computational Problem

The computational domain consists of a lossy dielectric hemi-cylinder(whose radius is Ri and complex permittivity is?)existing in air whose refractive index is unity.Since the domain is unbounded in nature,the perfectly matched layer(PML)whose mathematical formulation is introduced in[22]is utilized for domain truncation.Fig.2 presents the schematic of the targeted electromagnetic structure in Cartesian coordinates in which the incident waveEincpropagates in x-direction and polarized along z-axis.In this work,the wave source(Green’s function is assumed for clarity)is governed by the Helmholtz equation:

The field governed by the above equation decays rapidly as it propagates from the source location.That is;the assumption of such a radiating source is put in order to imitate the real situation of transmitting antenna in GHz ranges.The following frequency-domain Helmholtz equation must be satisfied inside the computational domain(except the PML):

whereEscastands for the scattered/transmitted field.Since?=1 is assumed around the hemicylinder,(9)reduces to the source-free homogenous Helmholtz equation.Discretizing the electromagnetics domain by SEM into elements requires more care than that in the case of finite difference or finite element method.This is due to the fact that irregular domains can be discretized by only deformed quadrilateral elements.A special type of meshing grid is deployed in the SEM in order to solve the field inside the computational domain.Gauss–Legendre–Lobatto(GLL)grids are used in the current work.In order to achieve the best accuracy offered by the SEM,Mahariq et al.[22]provided the optimum values of the attenuation factor associated to the number of nodes in GLLs.For the SEM formulation and SEM meshing,the reader may respectively refer to[22–26]for further details.A typical photonic nanojet at optical frequencies generated by illuminating a lossless dielectric micro-cylinder is shown in Fig.3 which is borrowed from[30].It is important to distinguish between lossy dielectric object at low frequencies and lossless cylinders at optical frequencies.For the latter case,for instance,extreme strong field localization is observed as reported in[31],however such a strong field can’t be realized in lossy cylinders at low frequencies.

Measurements of complex permittivity for several types of materials at wide range of frequencies have been performed in many studies[32–36].For instance,determination of permittivity for glass with planner and convex surfaces over a range of 75 MHz to 6 GHz is presented in[32],while the permittivity determination of polytetrafluorethylene,polyvinylchloride(PVC),and acrylic glass is performed at much higher frequencies and presented in Reference[33].In this work,the permittivity of polyoxymethylene is considered at 25 GHz.For this material,the real part of permittivity is?′=3.13 and tan(δ)=0.015.At these parameters,the radius of the cylinder is chosen as 2.85λin whichλdenotes the wavelength of the incident field.It should be mentioned that at this radius,strong field is realized behind the hemicylinder.

Figure 2:Schematic representation of the electromagnetic structure which includes a lossy dielectric hemi-cylinder excited by a z-polarized wave

Figure 3:A typical photonic nanojet at optical frequencies generated from a lossless dielectric micro-cylinder(Source[30])

In Fig.4,the solution of the electromagnetic structure as obtained by SEM is presented;(a)the colormapping of the total field magnitude is shown,(b)the 3D view of part(a),(c)the colormapping of the intensity,and in part(d)the corresponding field magnitude at y = 0 is plotted.The incident field is adjusted so that it takes a unit magnitude when it reaches the cylinder.In other words,the field plotted in Fig.3 is normalized with the incident one in order to realize the effect of the hemi-cylinder.

As it can be clearly seen from the Fig.4,the wave is focused and a beam of magnitude |E|of around 2.5 times the incident wave is formed behind the lossy dielectric cylinder,hence;the associate intensity is around 6 times the incident one.As one can observe,instead of having a scattering object that causes a significant disturbance to the incident wave,such a structure acts as a passive amplifier to the incident wave.Note that the scaling factor |E|is used in Section 3,Eqs.(3)and(6),to improve the overall system performance in terms of BER.It is worthy to note that the focused power is calculated from the beam intensity which is proportional to |E||E|*and is an associated characteristic to jet-like focusing[26–30].Therefore,the field magnitude,|E|,is the important quantity that is used in Eqs.(3)and(6).In the current proposed work,it is important to note that the reported measured complex permittivity values for the selected range of frequencies result in preferring hemi-cylindrical objects over full cylinders or spheres due to two facts;the first is associated in obtaining less transmission loss,and the second is to have the field focused and localized in areas where the relays can be placed.

Figure 4:The solution of the electromagnetic structure as obtained by SEM;(a)the colormapping of the total field magnitude,(b)the 3D view of part(a),(c)the colormapping of the field intensity,(d)the corresponding field magnitude at y = 0

As explained in the manuscript,we propose the addition of a hemi-cylindrical object(with a realistic complex permittivity values)that focuses the incident wave and hence amplifies the signal before it is just received by the wireless relay at communication frequency ranges.This focusing technique is emulated from photonic nanojets at optical frequencies.In order to verify the design,electromagnetic simulation is required to show that the field magnitudes are increased due to this proposed structure.The field magnitude is then used to prove that BER is decreased.

For this structure to be well utilized,the antenna of the receiver must be placed in the region where the wave focusing takes place.Fortunately,the focal point has almost stationary position and is dependent on material permittivity.Another important fact is that,if the transmitting source change its location over a range of around 30 degrees,the corresponding the focal point stays within the axis where the receiving antenna exists.The last two points in addition to others reported for photonic jets[37,38]are considered by the authors as a future work.In addition,other properties of photonic jets[39–41]may be emulated for the purpose of utilizing them in wireless relay networks.

5 BER Performance Analysis

6 Results and Discussion

In this section,we introduce the simulation results as well as the analytical results proposed in Section 5.Fig.5 shows the BERvs.the SNR of a wireless relay network composed of a transmitter T1,a receiver T2,with no direct link between them,and two relay nodes(R= 2)where the AF protocol is performed using 4-PSK,8-PSK and 16-PSK constellations.In this scenario,the proposed single-relay selection technique is compared with the best know single-relay selection technique[11,12]using two relay nodes(R= 2).More specifically,this figure shows the performance results of single relay selection strategies using the AF protocol with 4-PSK,8-PSK and 16-PSK modulation in the presence of two relay-nodes.

Figure 5:BER vs.SNR for single relay selection strategies using the AF protocol with 4-PSK,8-PSK,and 16-PSK modulations and R= {2}

Figure 6:BER vs.SNR for single relay selection strategies using the AF protocol with 4-PSK,8-PSK,and 16-PSK modulations and R= {3}

Figure 7:BER vs.SNR for single relay selection strategies using the AF protocol with 4-PSK,8-PSK,and 16-PSK modulations and R= {4}

Fig.5 shows the BERvs.the SNR of a wireless relay network composed of a transmitter T1,a receiver T2,with no direct link between them,and three relay nodes(R= 3)where the AF protocol is performed using 4-PSK,8-PSK and 16-PSK constellations.In this scenario,the proposed single-relay selection technique is compared with the best know single-relay selection technique[11,12]using three relay nodes(R= 3).Fig.7 shows the BERvs.the SNR of a wireless relay network composed of a transmitter T1,a receiver T2,with no direct link between them,and four relay nodes(R= 4)where the AF protocol is performed using 4-PSK,8-PSK and 16-PSK constellations.In this scenario,the proposed single-relay selection technique is compared with the best know single-relay selection technique[11,12]using four relay nodes(R= 4).Fig.7 shows the BERvs.the SNR of a wireless relay network composed of a transmitter T1,a receiver T2,with no direct link between them,and three and four relay nodes(R= {3,4})where the DF protocol is performed using BPSK constellations.

From Figs.5–7,we can clearly observe that our proposed single-relay-node selection technique outperforms the best-known single-relay selection technique[11,12]under all scenarios.Moreover,Fig.8 clearly shows that our simulation results match with our theoretical results given by(9)in Section 5.

Figure 8:Theoretical and simulated BER performance vs.SNR for the suggested strategy with R = 3 and R = 4

7 Conclusions

In this article,generation of photonic nanojet at optical frequencies resulted from illumination of lossless dielectric micro-cylinders is emulated for wireless networks frequencies.That is;we merged both,beamforming approach,and the optimal single-relay selection approach that is applied in wireless relay network,in the proposed strategy to get the benefits of both approaches.The beamforming approach calculated by SEM is modified to calculate the efficiency of the relay nodes while the relay selection method is improved to achieve the full diversity gain.Therefore,in this paper,an enhanced single relay selection strategy is introduced to be used for wireless relay networks using smart relays that offer higher coding gain and enjoy full diversity gain to improve the overall network performance in terms of BER.Furthermore,we proved the advantage of the proposed strategy analytically and through simulations.In our simulations,we show that our proposed strategy outperforms the best known state-of-the-art single relay selection technique.Furthermore,we proved that the BER results obtained from our conducted simulations are perfectly match those obtained from the theoretical analysis.

Funding Statement:This work was supported by College of Engineering and Technology,the American University of the Middle East,Kuwait.Homepage:https://www.aum.edu.kw.

Conflicts of Interest:The authors declare that they have no conflicts of interest to report regarding the present study.